Robótica Jobs

I’m building a compact, four-legged robot and need a mechanical designer who can take it from concept to validated CAD. Whether you prefer SolidWorks or Fusion 360 is completely up to you—the important part is a solid background in robotics mechanisms, joints, linkages, and gears, backed by a portfolio that shows assemblies in motion rather than static renders. Project scope The core task is a lightweight yet strong leg architecture. Each leg will have hip and knee joints that must offer a wide range of motion and allow precise control once the actuators and gearing are in place. Please reserve internal volume and mounting points for a Jetson board alongside a battery pack, and route cabling logically so the final build stays neat. What I expect from you • A full 3D ...

The task at hand is to turn a single concept image of my future battery-powered car into a realistic, build-ready electrical system. I already have people who can handle 3D work in Blender and the mechanical layout; what I need right now is someone who can own the electrical assembly side from concept through first prototype. You will translate the high-level vision into a complete, safe and serviceable setup—choosing the right motor and controller, sizing and arranging the battery modules, laying out both high- and low-voltage harnesses, and specifying all protection, charging and monitoring hardware. Along the way you will be collaborating closely with the Blender designer (for packaging and mounts) and the mechanical assembler (for brackets, cooling and enclosure requirements)....

I need to replace my old SmartDrive-i2c-P.i.D. driver because of this: where, after several attempts, it is proven that the SmartDrive i2c P.i.D. driver does not run (at maximum motor speed) both motors on my side simultaneously

I need three 7-10" quad-copters professionally put together and flight-tested in the UK. All the parts will be shipped directly to you; once they arrive I’d like the build, setup and maiden flights completed within roughly a week. Core spec: • Air-frames: 7-10" class • Electronics we will supply: FPV camera, GPS module and an onboard Raspberry Pi for extra processing • Flight controller: whatever board you are comfortable with, as long as the final stack runs PX4 flawlessly • Power: LiPo packs – please balance, secure and tune for safe discharge rates Your job starts with a clean assembly, neat soldering and reliable cable management, then moves on to firmware flashing, PX4 configuration, PID tuning and a short hover/flight test tha...

I’m building an autonomous mobile robot that handles pallets like a small forklift, and I need someone who can own the mechanical side from concept to production-ready files. Your core focus will be the chassis layout, all mechanical interfaces for sensors, drive units and forks, and the passive / active safety features that let the robot share space with people. A solid robotics background is important because every bracket, plate and cut-out has to coexist with navigation sensors, wiring looms and control hardware. I work in AutoCAD and would like the full model, detailed drawings and a clean BOM delivered in that environment. If you have supplementary tools in your workflow that’s fine, but the final artefacts must import cleanly into AutoCAD without lost constraints or met...

I need a working bridge that lets my Meta Quest 3 drive an igus ReBeL robot arm in real time over Wi-Fi. When I wear the headset I want to see and manipulate a 3-D model of the arm; every movement of my controllers or hands should be translated instantly into joint commands so the physical ReBeL mirrors my motion with minimal latency. You will handle both sides of the link: capturing pose data inside the Quest (Unity, Unreal or OpenXR—whichever you prefer) and streaming it wirelessly to the robot, then converting it into the motion commands accepted by the standard ReBeL control interface. A simple UI inside the headset that shows live joint angles and an emergency-stop button is also required. Deliverables: • Headset application for Quest 3 with live arm visualisation and con...

My drone’s flight control software is showing serious stability problems—unexpected pitch and roll changes that make the aircraft drift even in calm conditions. I need an engineer or developer who can dive into the existing flight-control codebase, pinpoint what is causing the instability, and implement a solid, tested fix. The job starts with a code review to isolate the root cause in the flight-control module, followed by refactoring or patching the affected algorithms (PID tuning, sensor fusion logic, or any timing issues you uncover). Once the fix is in place, I’ll need a compiled firmware image plus clear documentation of the changes so I can reproduce the build and flash future units. Acceptance criteria • Drone must hover and track waypoints without unexpe...

Por favor, regístrate o inicia sesión para ver los detalles.

I need a mechanical engineer to design me an automated machine to remote printed parts from my 3d printer, I have a PAROL6 robotic arm if that helps.