Desenho de Engenharia Jobs

I need a structural engineer to provide a wet stamp on construction plans and a structural analysis report for custom spiral stairs that have already been built. The stamp must comply with state building codes. Ideal Skills and Experience: - Licensed structural engineer - Experience with wet stamps - Familiarity with state building codes - Ability to review and approve construction plans and structural analysis reports

I am preparing a permit package for a new aluminum patio cover with a louvered roof and need a licensed structural engineer to design and stamp the plans. The frame and louvers will all be metal—specifically aluminum—so the calculations must reflect the lighter weight of the material as well as its deflection limits, wind loads, and any applicable snow or seismic requirements. You will receive site photos, rough sketches with dimensions, and local code references the moment we start. From there, I’m counting on you to size the beams, posts, footings, and connection details, then translate that work into clear, permit-ready drawings. Deliverables • PDF and DWG drawings showing plan, elevation, sections, and connection details • Structural load calculations th...

Saya ingin menghadirkan materi bertema impian dan cita-cita untuk siswa sekolah dasar yang ringan, menghibur, dan memotivasi. Fokusnya adalah membantu anak-anak mengenal berbagai profesi sekaligus menumbuhkan rasa percaya diri bahwa mereka dapat meraih apa pun yang mereka cita-citakan. Lingkup kerja yang saya bayangkan meliputi: • Cerita inspiratif pendek dengan bahasa sederhana dan ilustrasi ramah anak. • Aktivitas interaktif—misalnya lembar kerja atau kuis ringan—agar murid bisa merefleksikan minat serta bakatnya. • Petunjuk bagi guru atau orang tua agar mudah mengintegrasikan materi ini ke dalam pelajaran di kelas maupun belajar di rumah. Hasil akhir yang saya butuhkan dalam format digital (PDF atau sejenis) sehingga dapat langsung dicetak atau ditam...

I need a clean, well-organised Fusion 360 file that depicts an Oscillating Water Column (OWC) device in a way that engineers can immediately recognise and discuss. For this first phase I only require a visually accurate representation, yet it must still obey basic physics and align with published OWC literature so later optimisation studies can build on the same file. The model should show the overall geometry and relationships between the essential subsystems: • Air chamber • Turbine (generic runner is fine) • Water column and surrounding intake structure Moderate detail is ideal—enough to illustrate key internal volumes, clearances and material thicknesses without getting lost in fasteners or manufacturing minutiae. If you already have a library of standard ...

I need a designer who can take a bare rolling chassis and turn it into a fully-engineered commercial body—primarily box vans, curtainsiders, drawbars, de-mounts and dropsides. Each concept must bolt straight onto the chassis rails without re-drilling, meet local regulations and, above all, be robust and easy to assemble on the production line. Key design targets • Reinforced structures for daily fleet abuse and high load cycles • Modular interfaces so the same core panels and sub-frames can be reused across several body styles The workflow I have in mind begins with 3-D layouts (SolidWorks, Inventor or CATIA are fine), followed by strength calculations, basic CFD checks for frontal fairings when useful, and finally manufacturing drawings and BOMs. If you prefer anothe...

I need a detailed blueprint for a 24' x 44' garage that accommodates 3-4 vehicles. The design should be clear and professional, suitable for construction purposes. Ideal freelancers should have experience in architectural drafting and knowledge of garage layouts. Please include specifications and measurements for vehicle storage in the blueprint. Stamp Blueprints. one of the 24' sides will attach to the existing garage. 4/12 pitch roof. Blueprints also need to show footings and foundation.

I need a skilled designer to create pressure die casting molds for aluminum industrial machinery housings. Key requirements include: - Design precision for complex shapes - Expertise in aluminum die casting - Knowledge of industrial machinery specifications - Experience with CAD software Ideal skills and experience: - Background in mechanical engineering - Previous projects in die casting mold design - Strong attention to detail and problem-solving skills Please provide samples of past work and a brief project plan.

I need a professional to inspect the structural integrity of an existing residential bridge over a stream. The bridge is 10 years old, and I'm concerned about its condition. Requirements: - Thorough inspection of all structural components - Detailed report on current condition - Recommendations for any necessary repairs Ideal Skills and Experience: - Background in civil engineering or structural engineering - Experience with bridge inspections - Ability to identify potential issues and provide solutions

1. Objective of Instruction To obtain an independent, chartered‑level technical assessment of the soil‑stack installation serving Flat 32, including its offset configuration, ventilation provisions, and compliance with relevant standards, specifically: Approved Document H (Drainage & Waste Disposal) BS EN 12056‑2 (Gravity drainage systems inside buildings) CIPHE Soil & Waste Design Guide Manufacturer installation requirements (where applicable) The assessment should confirm or deny compliance and identify any design, installation, or performance defects. 2. Scope of Work Required A. Physical Inspection Inspect the soil‑stack riser section accessible from Flat 32. Identify all offsets, changes in direction, branch connections, and pipe gradients. Confirm pipe material, joint...

I need a slab design for a 14m x 8.5m shed, with a 2m concrete apron on all sides. The slab will support light tools and equipment, and needs to be reinforced. The second stage will be the house. Requirements: - Slab dimensions: 14m x 8.5m - 2m concrete apron on all sides - Reinforced concrete Ideal Skills and Experience: - Experience in designing reinforced concrete slabs - Knowledge of load-bearing requirements for light tools and equipment - Familiarity with concrete apron integration

I already have a complete civil site plan and utility plans for a forthcoming commercial project and simply need it signed, sealed, and dated by a Texas-licensed Professional Engineer. No redrafting or extra sheets are required; the drawings themselves are final. Scope • Review the provided PDF/CAD site plan to confirm it meets Texas standards for a commercial development. • Apply your PE seal along with your TBPE firm number and any required signature/date blocks. • Return the stamped file in the same format I supply (PDF) Acceptance A fully legible Texas PE stamp with your TBPE firm number on every required sheet, delivered electronically, completes the job.

I need assistance with the observation and installation of a standpipe piezometer system. Key Requirements: - Develop an installation plan based on provided drawing and specification _Supervise, record and stamp (by a lic geologist or geotechnical engineer) installation _Record asbuilts based on the data provided by the driller Ideal Skills and Experience: - Experience with piezometer installation - Ability to interpret and work from engineering drawings - Knowledge of soil and rock layer analysis Please provide relevant experience in your bids.

I need detailed production drawings created from existing CAD models for manufacturing purposes. The drawings should be in DXF format and include the following details: - Dimensions and tolerances - Material specifications - Finishing instructions Ideal Skills and Experience: - Proficiency in CAD software - Experience creating manufacturing drawings - Attention to detail and accuracy - Ability to work within budget constraints Looking for a freelancer who can deliver high-quality work efficiently. This is an ongoing role varying between 10-30 hours a week based on demand

We are looking for a highly experienced Solar PV System Designer with proven expertise in designing systems according to USA standards (NEC, IEEE, UL, etc.). The ideal candidate must have hands-on experience in commercial and industrial-scale solar projects, not just residential systems. Scope of Work: Design complete Solar PV systems (rooftop / ground-mounted) Perform load calculations and system sizing Prepare single line diagrams (SLD) Create detailed layout drawings (AutoCAD or similar) Equipment selection (inverters, panels, protection devices) Ensure compliance with US codes and standards (NEC) Provide bill of materials (BOM) -Simulation tools like Helioscope / PVsyst Requirements: Proven experience in US-based solar projects Strong understanding of NEC codes Experience with com...

I need a skilled structural engineer to: - Review basic structural drawings for an industrial containment shed inside a warehouse. - Create detailed design drawings. - Provide a comprehensive structural analysis report. - Sign off on the structural integrity. Ideal candidates should have: - Proven experience with industrial structures. - Expertise in both design and structural analysis. - Relevant certifications for structural sign-off. - Strong attention to detail and adherence to safety standards. Please include examples of similar projects in your bids.

I already have a fully detailed excavator CAD assembly and now need to turn it into a working motion model inside Siemens Simcenter 3D. The scope is limited to the digging and lifting cycle—boom, stick, bucket and their hydraulic actuators—so there is no need to model swing, rotation or travel. Your job is to import or link my CAD, define the joints, masses, centre-of-gravity data, hydraulic cylinders and motion drivers, then run a complete dynamic simulation of one full digging–lifting sequence. I’m particularly interested in actuator loads, reaction forces at the pins, power/energy consumption and overall cycle time, so please set up the appropriate sensors and output requests. Deliverable • A concise performance analysis report (PDF or Word) generated di...

I need a precise 2D AutoCAD drawing of an iron driveway gate with arches, based on my existing design. Requirements: - Accurate measurement of arches and radius - AutoCAD expertise - Detail-oriented and experienced with metal gate designs Ideal Skills: - Proficient in AutoCAD - Experience with 2D metalwork drawings - Strong attention to detail

I need MEP, CONSTRUCTION, BUILDING AUTHORITY DRAWINGS(FOR APPROVAL): I need construction detailed drawing of my building including all the details in 2D. Also need Mechanical, Electrical and Plumbing drawings in details. Need the required drawings for building approval for start construction. NOTE: Need all the drawings for basement, ground floor and above 3 floors. Architect with Pakistani building experience is preferable. Here’s the master list of all drawing types needed for building construction: ### *A. Architectural Drawings* 1. Site Plan / Key Plan 2. Floor Plans - all levels 3. Roof Plan 4. Elevations - 4 sides 5. Sections - longitudinal & cross 6. Reflected Ceiling Plan RCP 7. Door & Window Schedule 8. Finishing Schedule 9. Staircase Details 10. Lift/Elevator Deta...

I have a set of custom sheet-metal parts that now need clear, fabrication-ready 2D drawings. You will open my existing models in SolidWorks, create neat manufacturing drawings, and export each sheet as a DWG. The drawings must show every relevant view, accurately dimensioned—including bend lines, cut-outs, hole sizes, and material thickness—so a shop can cut and form the parts without questions. Where a feature is function-critical, add concise GD&T call-outs; no exhaustive feature control frames are required, just enough to lock down fit and alignment. Please keep the layout consistent with standard SolidWorks drafting conventions, apply my title block (I’ll send it), and use millimetre units throughout. All I need back is the clean DWG for each part; the native ...

The project consists of a multi-bay RHS/SHS steel frame forming part of an internal architectural installation (podium / lobby area), including wall connections, baseplates, and repeated modular sections. Drawings provided in both PDF and DWG format. Project Scope: You will be required to take the supplied design drawings and develop them into a fully resolved fabrication package suitable for direct workshop use. The frame includes: Repetitive vertical and horizontal RHS/SHS members Modular bay spacing and panel coordination Multiple connection types (wall fixings, cleats, baseplates) Integration with architectural elements (panels / finishes) Key Deliverables: 1. General Arrangement (GA) Drawings Fully dimensioned overall layout Setting-out information Grid / bay spacing clearly de...

I already have a well-developed silicone elephant toy/consumer product complete with DWG and STEP geometry; what remains is a concise engineering pass to incorporate my latest client feedback. The focus is twofold: • Filter system – please refine the internal filter so it delivers noticeably improved filtration efficiency. Geometry tweaks, flow path optimisation or any other creative engineering approaches are welcome, provided they integrate cleanly with the current body and stay injection-mould friendly for silicone. • Material adjustments – the part’s feel needs tuning. I need guidance on altering hardness/flexibility and selecting a more suitable silicone grade that meets the revised shore requirements while maintaining food-grade safety. * Scale needs ...

I need detailed architectural floor plans produced in Autodesk software. You will be turning my sketches and notes into clean, accurate drawings that can be issued to consultants and expanded later into full construction documentation. The drawings must be created entirely in AutoCAD or Revit, drawn to real-world scale, and organised on sensible layers so elevations and sections could be added in the future. Please include walls, doors, windows, fixtures, room names and clear overall and partial dimensions. Deliverables • Dimensioned floor plan in the native Autodesk file format (.dwg or .rvt) • PDF sheet ready for printing at 1:100 or 1/8" = 1'-0" • All line work cleaned (no duplicate or stray entities) and layers named to a recognised standard I w...

I need detailed as-built drawings for a sanitary sewer project. These drawings are primarily for documentation to ensure future maintenance is straightforward and efficient. Key Requirements: - Accurate representation of manhole locations and elevations - Detailed mapping of the sanitary sewer system - Precision in all measurements and annotations Ideal Skills and Experience: - Proficiency in CAD software - Experience with sewer system documentation - Attention to detail and accuracy in engineering drawings Looking for a freelancer who can deliver high-quality, precise work.

I’m working on the next-generation gear systems that will drive our CNC turning centres, vertical machining centres, and multi-axis machines. What I need right now is a fresh, precise mechanical design for those individual gear components—everything from tooth profile definition through tolerance-ready manufacturing drawings. Here’s what the collaboration looks like: • Scope ‑ Purely mechanical design: no electronics or control work this round. ‑ Component-level focus: shafts, pinions, spur/helical gears and their mating relations inside the gearbox. ‑ The design must integrate smoothly with our existing machine envelopes and lubrication layouts at JYOTI CNC Automation Ltd. • Typical workflow 1. You receive my baseline requirements, speed/torq...

I have a mechanical component that now exists only as an idea and a few rough sketches. I need it turned into a clean, fully-parametric 3D model in SolidWorks, then documented with precise 2D manufacturing drawings in AutoCAD. You will start in SolidWorks, building the part (or small assembly) so every dimension can be updated later without the model breaking. Once the model is complete and I sign off on its geometry, export the critical views to AutoCAD and create fabrication-ready drawings that follow standard mechanical drafting conventions—clear dimensions, tolerances where noted, and a proper title block. Native SolidWorks files, STEP/IGES interchange formats, and DWG/DXF drawings must all be delivered. I expect the SolidWorks feature tree to remain editable and clearly name...

Project description I’m seeking a CAD technician or architectural technologist to produce a small set of early‑stage concept and technical‑intent drawings for a modular infrastructure product. The design is already defined (overall geometry and key dimensions are fixed). I am not looking for design development, compliance drawings, or construction details at this stage. The task is to translate existing intent into clear, professional drawings suitable for early technical discussions. Scope (indicative) 1 general arrangement plan 1–2 elevations 1–2 key sections I will provide sketches, reference dimensions, and written guidance. Requirements Strong 2D CAD skills (AutoCAD or similar) Experience preparing plans, sections, and elevations Comfortable working from provide...

I have a consumer-oriented packing concept that feeds items into plastic sleeves, heat-seals them, and advances to the next cycle. The core idea is solid and I need detailed drawings, and the mechanics. I now need these drawings converted into a fully engineered, test-ready design. Your task is to transform the concept into a complete 3D CAD assembly, flesh out every moving part, and specify the materials that will survive repeated heat, friction and load. I want to see how the film advances, where the sealing jaws sit, how the drive train engages and resets—every cam, gear or actuator modelled so we can simulate the full feed-seal-cut sequence before metal is cut. Deliverables • Parametric 3D model of the entire mechanism (SolidWorks, Fusion 360 or comparable) • Detail...

I need a practical yet accurate fixture that holds a mostly sheet-metal frame square and true while it is being welded. The structure also incorporates a few tubes and standard hardware, so the jig must secure mixed-section parts and guarantee that the finished weldment drops straight into the adjacent machine assembly with no re-work. All critical sizes of the final frame are already known; your task is to create the fixture concept, produce full 3D CAD and 2D drawings, and write a brief operator guide so any welding technician can load parts and clamp them in minutes. Tight tolerances should be achieved through sensible datums, locator pins and repeatable stops rather than complicated mechanisms—the goal is simplicity, speed and consistency. Because the primary material is tube a...

Scope of Work: Road and Fencing Longitudinal & Cross Sections The assignment involves the preparation of longitudinal and cross-sections of the road along with the existing roadside fencing levels. The objective is to develop a new proposal for fencing at road level wherever the existing fencing is found to be below the road level. Deliverables Longitudinal Sections: One longitudinal section for the road. One longitudinal section for the roadside fencing. Both sections to be presented in the same plan, using different colors to clearly illustrate level differences. Cross Sections: At required intervals to capture road and fencing conditions at different levels. Demarcation Plans: Existing Road alignment. Existing Fencing positions. Proposed Fencing adjustments at road level. ...

I need a solution to automate repetative tasks in CATIA, specifically in drawing generation and quality checks. Key Requirements: - Automation of dimensioning and annotation in drawing generation - Quality check automation - Experience with CATIA and automation tools Ideal Skills and Experience: - Proficiency in CATIA - Experience with automation scripts or tools - Strong background in CAD and engineering drawings Looking for a freelancer who can streamline my CAD processes and reduce manual effort.